Ball Valve

Product Details:

SQK Ball valves

A Ball valve is a quarter-turn rotational motion valve that uses a ball-shaped disk to stop or start flow. If the valve is opened, the ball rotates to a point where the hole through the ball is in line with the valve body inlet and outlet. If the valve is closed, the ball is rotated so that the hole is perpendicular to the flow openings of the valve body and the flow is stopped.

Types of Ball valves

Ball valves are basically available in three versions: full port, venturi port and reduced port. The full-port valve has an internal diameter equal to the inner diameter of the pipe. Venturi and reduced-port versions generally are one pipe size smaller than the line size.

Ball valves are manufactured in different body configurations and the most common are:

• Top entry Ball valves allow access to valve internals for maintenance by removal of the valve Bonnet-cover. It is not required to be removed valve from the pipe system.
• Split body Ball valves consists of a two parts, where one part is smaller as the other. The ball is inserted in the larger body part, and the smaller body part is assembled by a bolted connection

The valve ends are available as butt welding, socket welding, flanged, threaded and others.

Materials - Design - Bonnet

MATERIALS

Balls are usually made of several metallics, while the seats are from soft materials like Teflon®, Neoprene, and combinations of these materials. The use of soft-seat materials imparts excellent sealing ability. The disadvantage of soft-seat materials (elastomeric materials) is, that they are not can be used in high temperatures processes.

For example, fluorinated polymer seats can be used for service temperatures from −200° (and larger) to 230°C and higher, while graphite seats may be used for temperatures from ?° to 500°C and higher.

STEM DESIGN

The stem in a Ball valve is not attached to the ball. Usually it has a rectangular portion at the ball, and that fits into a slot cut into the ball. The enlargement permits rotation of the ball as the valve is opened or closed.

BALL VALVE BONNET

The Bonnet of a Ball valve is fastens to the body, which holds the stem assembly and ball in place. Adjustment of the Bonnet permits compression of the packing, which supplies the stem seal. Packing material for Ball valve stems is usually Teflon® or Teflon-filled or O-rings instead of packing.

Ball valves applications

The following are some typical applications of Ball valves:

• Air, gaseous, and liquid applications
• Drains and vents in liquid, gaseous, and other fluid services
• Steam service

Advantages and Disadvantages of Ball valves

ADVANTAGES:

• Quick quarter turn on-off operation
• Tight sealing with low torque
• Smaller in size than most other valves

DISADVANTAGES:

• Conventional Ball valves have poor throttling properties
• In slurry or other applications, the suspended particles can settle and become trapped in body cavities causing wear, leakage, or valve failure.

Product Details:

Under the command of our trained personnel, we are able to offer the collection of Trunnion Mounted Ball Valve.These products are highly acclaimed for their quality and economical prices.We offer these to our clients in a wide range of specifications in customized and standardized forms.Our professionals manufacture these products using high grade raw material and advanced technology in accordance with the set industry standards. This range is offered with customized solutions so as to suit the different requirements of our patrons. 

Features:

• Sturdy design
• Excellent finish
• Durability

Product Details:

With an objective to fulfill the ever evolving demands of our clients, we are engaged in offering a wide assortment of Three Piece Ball Valve

Product Details:

With an objective to fulfill the ever evolving demands of our clients, we are engaged in offering a wide assortment of Flanged Ball Valve

Product Details:

With an objective to fulfill the ever evolving demands of our clients, we are engaged in offering a wide assortment of Gear Operated Ball Valve

Product Details:

With an objective to fulfill the ever evolving demands of our clients, we are engaged in offering a wide assortment of Ball Valves

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Product Details:

Product Details:

Being into the business of manufacturing, exporting and supplying, we have been able to serve our clients with an extensive range of Industrial Floating Ball Valve.These products are highly sturdy in quality, as designed with the superior-quality components obtained from the specialized vendors of the market.The offered valve is widely praised by the clients, owing to its varied quality features.Our offered ball valves are checked on numerous parameters by quality experts for delivering a defect free range. 

Features:

• Increased operation efficiency
• Optimum quality
• Anti corrosive

Product Details:

Jacketed Ballvalves offer all the proven design attributes of standard 2-way valves and are available in a wide range of different jacket connections.

Typical applications:
Jacketed valves are especially used for media that might crystallize or seize and therefore must be influenced through additional heating or cooling.

Design Features and Benefits:
The welded jackets consisting of two shells reach from flange to flange and assure consistent valve heating or cooling of the process media to prevent crystallization or seizing of flow media. This applies especially to media like bitumen, liquid sulfur, resins, etc. In addition, the efficient flow of media is ensured through the elimination of pockets. Oil, steam, water, brine can be used as carrier for heating or cooling media. The special valve design allows the hydrostatic and pneumatic examination of the valve body prior to the jacket welding process. Following our quality assurance rules, every valve is tested again after the jackets have been welded to the body

Product Details:

With an objective to fulfill the ever evolving demands of our clients, we are engaged in offering a wide assortment of Two Piece Ball Valve

Product Details:

With an objective to fulfill the ever evolving demands of our clients, we are engaged in offering a wide assortment of API Ball Valve

Product Details:

With an objective to fulfill the ever evolving demands of our clients, we are engaged in offering a wide assortment of Carbon Steel Ball Valve

Product Details:

With an objective to fulfill the ever evolving demands of our clients, we are engaged in offering a wide assortment of Cast Carbon Steel Ball Valve

Product Details:

With an objective to fulfill the ever evolving demands of our clients, we are engaged in offering a wide assortment of Single Piece Ball Valve

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Product Details:

With an objective to fulfill the ever evolving demands of our clients, we are engaged in offering a wide assortment of Forged Stainless Steel Ball Valve

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece

BALL VALVES

Trunnion-mounted Ball Valves

·         Trunnion-mounted Ball Valve design complies to API 6D

·         Wide portfolio of Side-entry and Top-entry designs

·         Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH

·         Firesafe design - to API 607 and API 6FA

·         CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU,

·         Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required

·         Double block and bleed (DBB) feature - Valves are designed and tested for automatic cavity relief

·         Anti-blowout stem design

·         Coil springs used for consistent seat loading and lower operating torque

·         Lip seals provided for low temperature services

·         Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary)

·         Wide portfolio of Side-entry and Top-entry designs

·         Options: Buried service, Cryogenic

·         Offered with Electric, Pneumatic and Hydraulic Actuators

·         In-house Tests Capabilities

 

 

Floating Ball Valves

We manufacture a wide range of Process Ball Valves in single, two and three piece constructions. The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements.

The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.

·         Fire-safe to ISO 10497 and API 607

·         Mirror-finished solid stainless ball

·         Fine-grained PTFE seats

·         Cavity Pressure Relief mechanism

·         Blowout-proof stem

·         High integrity stem sealing – Belleville springs compensate for wear and thermal expansions

·         Antistatic feature

·         Actuator-mounting flange conforms to ISO 5211

·         Single, two and three piece constructions

·         Full-bore and regular-bore designs

·         Soft and metal-seated

·         Offered in carbon steel, stainless steel and duplex stainless steels

·         Screwed, socket-weld and flanged ends

·         ASME classes up to 2500

Additional Information:

• Minimum Order Quantity: 1 Piece